EXPOL COATED EDGE INSULATION 10 YEAR PRODUCT WARRANTY

WHO IS COVERED

If you live in New Zealand and you are the original consumer purchaser (i.e., the homeowner or building owner, not the builder, installer or contractor) or any transferee tracing back to the original consumer purchaser (the “Purchaser”) of Slab Edge Insulation, you are entitled to the benefits of this warranty.

WHAT IS COVERED

EXPOL, subject to the conditions and limitations set forth herein, warrants that its Slab Edge Insulation shall, from the date of installation and for 10 years of the home or building in which originally installed, when such Slab Edge Insulation shall have been properly installed and when subject to normal and proper use:

• Be free from defects in material and/or workmanship that materially affect its performance in the home or building in which originally installed.
• Meet performance requirements as detailed in the EXPOL ThermaSlab Edge Technical Data Sheet or EXPOL MAXEdge Technical Data Sheet, as applicable (2022 and beyond).
• Retain at least 80% of its advertised R-value. *

*R-value means resistance to heat flow. The higher the R-value the greater the insulating power

EXPOL’s obligations under this warranty will only take affect if the Slab Edge Insulation is installed (including both the original installation and reuse installation) in typical building and construction assemblies in strict accordance with all applicable EXPOL specifications, recommendations and guidelines that were in effect at the time of such installation. Slab Edge Insulation shall only be placed into an assembly where the moisture transport mechanism is well understood and determined to be acceptable in accordance with accepted engineering analytical practice.

REMEDY

If, during the warranty period and because of a covered defect in material or manufacturing, the Slab Edge Insulation is determined by sampling and tests (conducted as provided below) to not meet any of the performance requirements stated above, as Purchaser’s sole remedy, EXPOL will deliver to the Purchaser a quantity of equivalent EXPOL product to replace the non-performing Slab Edge Insulation product or, at EXPOL’s sole discretion, refund to the Purchaser the original purchase price of the non-performing EPS Foam Insulation product.

EXPOL’s TOTAL LIABILITY/COST HEREUNDER, FOR THE LIFE OF THE WARRANTY, IS LIMITED TO, AND CAPPED AT, THE ORIGINAL PURCHASE PRICE OF THE SLAB EDGE INSULATION PRODUCT.

WHAT IS NOT COVERED

This warranty does not apply to and EXPOL shall not be liable for any cause not expressly covered herein. This warranty does not cover any problems with non-defective material caused by conditions or handling beyond our control.

Some examples of conditions not covered by this warranty include failures or defects in the Slab Edge Insulation caused by:

• Causes beyond normal and proper use including, but not limited to, acts of God, war or terrorism, fire, flood, wind or other weather damage, exposure to chemicals or the environment; or
• Failures or distortions in the building structure, or improper installation of neighbouring products; or
• Failure to install the Slab Edge Insulation strictly in accordance with EXPOL’s published installation instructions for the Slab Edge Insulation product; or
• Failure to install the Slab Edge Insulation in compliance with all applicable building codes; or
• Damage to the Slab Edge Insulation caused by alterations made after completion of installation, including but not limited to structure changes, equipment installation, or other modifications; or
• Non-manufacturing defects, including but not limited to improper storage, improper maintenance, neglect, accident, casualty, vandalism or misuse of the Slab Edge Insulation, or any other cause that disturbs or disrupts the Slab Edge Insulation as installed; or
• Any costs incurred by you that are not authorized in writing, and in advance, by EXPOL.

Further, this warranty does not apply to and EXPOL shall not be liable for the compatibility of any other product (including, but not limited to adhesives or coatings, other than those specified) with the Slab Edge Insulation product.

This warranty shall be voided if, in EXPOL’s judgement, either damage or alteration of the Product (without prior EXPOL written approval) has impaired Product performance.

LIMITATIONS ON COVERAGE

THIS WRITTEN WARRANTY IS YOUR EXCLUSIVE WARRANTY FROM EXPOL AND REPRESENTS THE SOLE REMEDY TO THE PURCHASER OF EXPOL MANUFACTURED SLAB EDGE INSULATION PRODUCTS.

EXPOL MAKES NO OTHER REPRESENTATIONS, WARRANTIES OR GUARANTEES OF ANY KIND OTHER THAN THOSE STATED EXPLICITLY HEREIN.

THE WARRANTY PROVIDED IS IN LIEU OF ALL OTHER GUARANTEES AND WARRANTIES EXPRESSED OR IMPLIED. THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE EXPRESS WARRANTY PROVIDED HEREIN UNLESS A SHORTER PERIOD IS PERMITTED BY LAW.

EXPOL DOES NOT ASSUME AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY FOR ANY INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, PUNITIVE OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR COSTS TO REMOVE AND/ OR REPLACE PRODUCT, INCREMENTAL HEATING, COOLING OR SIMILAR COSTS, AND ANY OTHER HARM TO THE BUILDING, IT’S CONTENTS OR ITS OCCUPANTS, OR TO ANY OTHER PERSONS OR PROPERTY, WHETHER FOR BREACH OF THIS WARRANTY, NEGLIGENCE, STRICT LIABILITY OR OTHER CLAIMS DERIVED IN TORT, OR FOR ANY OTHER CAUSE.

CLAIMS PROCESS

To make a claim under this warranty, you need to do so within thirty (30) days after you discover the problem. A letter sent to EXPOL, PO Box 13 560, Onehunga, AUCKLAND 1643. Explain the problem and include proof of purchase for the Product and the date it was installed. Shortly after we receive your communication, we will contact you regarding your claim and will walk you through the entire process.

To fully evaluate your claim, we may require that testing be done on the product as specified in the Insulation Testing section of this warranty.

If you have any questions, write us at the afore mentioned address, or call us anytime on 0800 86 33 73 Alternatively – visit our website at www.expol.co.nz

INSULATION TESTING

All sampling shall be conducted in accordance with sampling procedures prescribed by EXPOL and samples of the Slab Edge Insulation product shall only be taken in the presence of an authorized EXPOL representative. Testing shall be conducted in conformance with the testing protocols AS4859 – 2018, ASTM C518 and AS1366 – 1992.

SAMPLING REQUIREMENTS

• All sampling and testing costs (including but not limited to costs of insulation covering removal and replacement) shall be at the Purchaser’s sole expense.
• The samples selected shall be representative of the Slab Edge Insulation product in question.
• A minimum of three samples shall be selected.
• The samples shall be 600 x 600mm for the full thickness.
• The exact location of sampling shall be at the discretion of the home or building owner, or his/her representative.
• All sampling shall be done in the presence of a EXPOL representative.
• All testing shall be conducted at a BRANZ, OPUS or AWTA lab or equivalent.

MODIFICATION OF THIS LIMITED LIFETIME WARRANTY

This warranty shall not be changed, modified or extended except by written instrument signed by an officer of EXPOL. No statement or recommendation made, or assistance given by EXPOL, or its representatives, either oral or in any literature or other documentation, to Purchaser or any other persons in connection with the purchase, use or installation of the Slab Edge Insulation product by or for the Purchaser, shall constitute a waiver by EXPOL of any provision hereof or affect EXPOL’s liability as defined in this warranty.